Search results

I had this problem before. With many wires off the same post, I would tape or wire tie them in a bundle. Its just too easy to miss one.

I would look for a short in the harness than. If that fails. New wiring then. It's a simple install.

You mean, its by-passing the switch. Yes?

I am a little confused. So all 5 wires are disconnected and the 2 blowers stay on? If that is the case, " then they are getting their power from another wire that is powered by that same breaker." I would try to trace the wires from the blowers to the breaker. Or even the other way too. You...

At 12V, they make them way bigger than that. But there more money.

I don't thing you need to set the sending unit to point to a devices. Most likely, and true with Simrad. On the receiving unit. you need to pick the device you want the data from. In my case, I have 2 sonar transducers and 2 devices that give GPS locations. I had to pick which device to take...

I always kept it stocked. So I would not have to bring down the condiments and other stuff.

I don't use my grill that often. But that's me.. As to the fridge, more facts are needed. You must do the math. How many amp does the fridge use? How many amp hours are you 2 batteries? Now add in what you will use in one day. Without that info, your question can not be answered. Just an FYI...

You are better off coming off the engine. No different than a hot water heater found on most boats. Cut a hose and put the heater in line. This works great with a closed cooling system. On a open system, its going to run a little cooler. The only electric ones run off of 120v. Which means...

Videos, I would do a You Tube search. Just an FYI - I have no experience with Merc. If I was having a problem, the first thing I would do is download the latest firmware to both Simrad and Smart Craft equipment. From there you'll need a Mercury VesselView Link or SmartCraft Connect module...

Thank you!

Its all on the weather. It can be like glass, but normally we are traveling in in 1 ft or less seas. But it happens, we can hit 2 to 3 foot waves. Buzzards Bay coming out of the Cape Cod Canal gets a little crazy due the tides moving back and forth. Its not uncommon to stay put for a day or two...

North is up in the Pic. The blue line is my route. Block Island is to the N.E. My route stops at Sag Harbor, the triangles are the boats with AIS with is clouding the chart up. 3 Mile Harbor is to the right of Sag Harbor. It was about a 150 mile run from Boston. We did stop at Cuttyhunk for 2...

I would follow the fuel line from the tank. If you one, than there is none. I had a Sig 290, I added a Racor filters to each engine. I wanted to make sure that dirt and water never reaches the engines. This is what I added, but thats me...

I would first clean the pump. Something may be causing the impeller not to spin. I suggest to always carry a spare pump. South shore of L.I. I went to Sag and 3 Mile Harbor by boat 2 weeks ago.

Most gauges are off the shelf stuff. You just need to match the specs of the old to new. I will use fuel a gauge as an example. Some are rated 0-30ohms or 0-90ohms. Some have a switches to match the sending unit. It really depends on what you pick. Do you have analog or digital? Around 2010...

You can always relocate the pump.

I would fellow the supply line off the tank. That should take you to it.

I always try to go big. Tolling motors for a main engine really don't do well. Something like this would be a better solution. https://defender.com/en_us/torqeedo-440w-tiller-electric-outboard-motor-travel-903c Its light, shows battery status and more. But pricy. Don't forget, with a trolling...

Have you thought about the size battery/s needed vs its time in use? Also recharging?